Adc CRA-C Uživatelský manuál Strana 12

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 86
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 11
About the Megabit Modem CRA-C
4 Megabit Modem CRA-C User Manual
Reach, Data Rate, SNR Margin, and Noise Environment
The maximum transmission rate of the Megabit Modem CRA-C is determined
by distance, SNR margin, and the condition of the line (wire gauge, condition
noise environment). Figure 1 shows the relationship between reach and data
rate for a given set of conditions. The plots can be used to determine the
achievable reach at a given data rate, or they may be used to determined the
achievable data rates at a given distance. In all of the cases except the no
noise case, a margin of 6 dB was allocated above the SNR that provides a Bit
Error Rate (BER) of 10
-7
.
These line conditions fall within the range of the plots shown in Figure 1:
no noise (0 dB margin)
low noise (140 dBm-Hz Additive White Gaussian Noise (AWGN))
24 ISDN lines in the same binder group
24 HDSL lines in the same binder group
24 ADSL lines in the same binder group
10 T1 lines in an adjacent binder group
one T1 line in the same binder group
The performance shown is "typical" for PairGain Megabit
Modem CRA products. Due to variations in environment and
test setup, PairGain does not guarantee performance to the
figures shown.
One of the configuration options in the Megabit Modem CRA-C is the
startup margin setting. This setting defaults to 6 dB but may be set from
-3 dB to 9 dB. The modems will attempt to come up at the programmed
margin setting. Setting the margin high allows for a cushion against changing
line conditions and impulse noise. Setting the margin low provides less
protection but allows the modems to come up at a higher data rate (if in the
rate-adaptive modes) or at a longer loop length (if in the fixed data rate mode).
The default setting of 6 dB is recommended and provides an overall BER
better than 10
-10
. Reducing the setting to 0 dB will only provide a BER of
less than 10
-7
and is not recommended.
Zobrazit stránku 11
1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 85 86

Komentáře k této Příručce

Žádné komentáře

Seagate BARRACUDA ST31500541AS manuály

Uživatelské manuály a uživatelské příručky pro Hardware Seagate BARRACUDA ST31500541AS.
Poskytujeme 1 manuály pdf Seagate BARRACUDA ST31500541AS ke stažení zdarma podle typů dokumentů: Uživatelský manuál






Další produkty a příručky pro Hardware Seagate

Modely Typ Dokumentu
DB35 Serial ATA ST3250823SCE Uživatelský manuál   Seagate DB35 Serial ATA ST3250823SCE User Manual, 44 stránky
BARRACUDA ST3500620SS Uživatelský manuál   Seagate BARRACUDA ST3500620SS User Manual, 82 stránky
SV35.5 SERIES SATA ST31000525SV Uživatelský manuál   Seagate SV35.5 SERIES SATA ST31000525SV User Manual, 46 stránky
Ultra 320 Uživatelský manuál   Seagate Ultra 320 User Manual, 186 stránky
Barracuda ST3120211AS Uživatelský manuál   Seagate Barracuda ST3120211AS User Manual, 50 stránky
Pipeline HD Mini Series SATA ST9250311CS Uživatelský manuál   Seagate Pipeline HD Mini Series SATA ST9250311CS User Manual, 48 stránky
BARRACUDA ST32000542AS Uživatelský manuál   Seagate BARRACUDA ST32000542AS User Manual, 46 stránky
CONSTELLATION ES SERIAL ATA ST31000524NS Uživatelský manuál   Seagate CONSTELLATION ES SERIAL ATA ST31000524NS User Manual, 48 stránky